32 + 2 fader configuration adapts to a wide range of channel layouts. The QL5 is a compact console with large-scale capabilities.


  • Mix channels : 64 mono, 8 stereo.
  • Busses : 16 mix, 8 matrix (Input to Matrix supported).
  • Local I/O: 32 in, 16 out.
  • Fader configuration: 32 + 2 (Master).
  • Stainless steel iPad support stays.

 

General specifications

Sampling frequency rate Internal 44.1kHz / 48kHz
External 44.1kHz: +4.1667%, +0.1%, -0.1%, -4.0% (±200ppm), 48kHz: +4.1667%, +0.1%, -0.1%, -4.0% (±200ppm)
Signal delay Less than 2.5ms, INPUT to OMNI OUT, Fs= 48kHz
Fader 100mm motorized, Resolution=1024steps, +10dB to –138dB, –∞dB all faders
Total harmonic distortion Less than 0.05% 20Hz-20kHz@+4dBu into 600Ω, INPUT to OMNI OUT, Input Gain= Min.
Frequency response +0.5, -1.5dB 20Hz-20kHz, refer to +4dBu output @1kHz, INPUT to OMNI OUT
Dynamic range 112dB typ.: DA Converter / 108dB typ.: INPUT to OMNI OUT, Input Gain = Min.
Hum & noise level Equivalent input noise -128dBu typ., Equivalent Input Noise, Input Gain=Max
Residual output noise -88dBu, Residual output noise, ST master off
Crosstalk -100dB*1, adjacent INPUT/OMNI OUT channels, Input Gain = Min.
Power requirements 100-240V 50/60Hz
Power consumption 200W
Dimensions W 828mm(32.6in)
H 272mm(10.7in)
D 563mm(22.2in)
Net weight 21.8kg(48.1lb)
Accessories Owner’s Manual, dust cover, power cord, DVS license sheet
Options Mini-YGDAI cards *2 , Gooseneck Lamp LA1L, Nuendo Live
Others Operating temperature range: 0 - 40℃, Storage temperature range: -20 - 60℃

Crosstalk@1kHz : A 22kHz, 30dB/Oct filter is used to measure crosstalk.
Total Harmonic Distortion : An 80kHz, 18dB/Oct filter is used to measure total harmonic distortion.
Hum & Noise : An A-Weight filter is used to measure hum &noise.

Analog input characteristics

Input Connectors GAIN Input
Impedance
Source
Impedance
Input level Connector
Sensitivity*¹ Nominal Max. before clip
INPUT
1-32 *6
+66dB 7.5 kΩ 50-600 Ω
Mics &
600 ΩLines
–82dBu
(61.6μV)
–62dBu
(0.616mV)
–42dBu
(6.16mV)
XLR-3-31
type
(Balanced) *2
–6dB –10dBu
(245mV)
+10dBu
(2.45V)
+30dBu
(24.5V)

*1. The sensitivity is the input level required for output at +4dBu (1.23V) or at the defined level when all the faders and level
controllers are set to the maximum value.
*2. XLR-3-31 connectors are balanced jacks (1=GND, 2=HOT, 3=COLD).
*3. 0dBu=0.775 Vms for all specifications.
*4. All the AD converters use 24-bit linear/128-times oversampling.
*5. The INPUT connectors have +48V DC (phantom power) jacks, each of which can be turned on/off individually from the console software.
*6. QL1: INPUT1-16

Analog output characteristics

Output
Connectors
Output
Impedance
Load
Impedance
Maximum
Output
Level *5
Output Level Connector
Defined Level Maximum
Non-Clip Level
OMNI
OUT 1-16 *7
75 Ω 600 Ω
Lines
+24dB
(default)
+4dBu
(1.23V)
vt+24dBu
(12.3V)
XLR-3-32 type
(Balanced) *1
+18dB –2dBu
(616mV)
+18dBu
(6.16V)
PHONES 15 Ω 8 Ω
Phones
- 75mW *6 150mW Stereo Phone
Jack(TRS)
(Unbalanced) *2
40 Ω
Phones
- 65mW *6 150mW

*1. XLR-3-32 connectors are balanced jacks (1=GND, 2=HOT, 3=COLD).
*2. The PHONES connectors for stereo headphones are balanced jacks (Tip=LEFT, Ring=RIGHT, Sleeve= GND).
*3. 0 dBu=0.775 Vms for all specifications.
*4. All the DA converters use 24-bit linear/128-times oversampling.
*5. The console has an internal switch for toggling the maximum output level.
*6. This is a value measured with the PHONES LEVEL knob set to 10 dB below the maximum position.
*7. QL1: OMNI OUT 1-8

Digital input/output specifications

Connectors Format Data length Level Audio Connector
Primary/Secondary Dante 24bit or 32bit 1000Base-T 64ch Input/64ch
Output@48kHz *1
EtherCON Cat5e

*1. QL1: 32ch Input/32ch Output@48kHz

Digital output specifications

Connectors Format Data length Level Connector
DIGITAL OUT AES/EBU AES/EBU Professional Use 24bit RS422 XLR-3-32 type (Balanced) *1

*1. XLR-3-32 connectors are balanced jacks (1=GND, 2=HOT, 3=COLD).

I/O SLOT (1-2) specifications

Each I/O Slot accepts a Mini-YGDAI card.
Only Slot 1 has a serial interfac

Control I/O characteristics

Connectors Format Level Connector
MIDI IN MIDI - DIN Connector 5P
OUT MIDI - DIN Connector 5P
WORDCLOCK IN - TTL/75 Ω terminated BNC Connector
OUT - TTL/75 Ω BNC Connector
GPI (5IN/5OUT) - - D Sub Connector 15P(Female) *1
NETWORK IEEE802.3 10BASE-T/100Base-TX RJ-45
LAMP (QL5: x 2, QL1: x 1) - 0V-12V XLR-4-31 type *2
USB HOST USB 2.0 - USB A Connector (Female)

*1. Input pin: TTL level, w/ internal pull-up (47kΩ) Output pin: Open drain output (Vmax=12V, maximum sink current/pin=-75mA) Power supply pin: Output voltage Vp=5V, Max. output current=300mA
*2. 4 pin=+12V, 3 pin=GND, Lamp nominal power: 5W, Brightness (voltage) can be adjusted from the software.

Напиши мислење

Белешка: HTML не е дозволен!
    Лош           Добар

Yamaha QL5

  • UPC:
  • Достапност: Јавете се
  • 1.032.600,00 МКД
  • 996.000,00 МКД


Слични продукти

Zoom L-8

Zoom L-8

Zoom LiveTrak L-8 makes it easier than ever to mix, monitor and record professional-sounding podca..

32.000,00 МКД

Yamaha CL5

Yamaha CL5

With a three-section fader layout for efficient hands-on control, the CL5 is the ideal choice for a ..

1.764.000,00 МКД

Yamaha DM7 Compact

Yamaha DM7 Compact

Go Above and Beyond! DM7 series mixing consoles represent a sizable step forward in this evolution..

1.054.000,00 МКД

Yamaha QL1

Yamaha QL1

16 + 2 fader configuration in a compact, rack mountable unit. Mix channels : 32 mono, 8 s..

549.000,00 МКД

Ознаки: Yamaha QL5