EMX2 is both a mixer and a power amplifier. Lightweight and portable design make it very easy to carry and particularly useful for various events.

Because the EMX2 is both a mixer and a power amplifier, you only need speakers and mics to have a fully functioning sound system. This makes it easy for newcomers, and even first-time users with no previous audio experience to easily configure their own sound reinforcement system. The EMX2's all-in-one design concept ensures that by just plugging in a single power cable and making a few simple, intuitive connections, anyone can be their own sound engineer.

Outline

I/O	Inputs	TOTAL 10ch : Mono (MIC/LINE):4, Stereo(LINE):3
	Phantom power	CH1, 2 : +30 V
	Outputs	SPEAKERS [L, R], MONITOR OUT [L,R], SUBWOOFER OUT
	Control and others	FOOT SW : Effect Mute on/off
Bus		Stereo: 1, Effect: 1
Input Channel Function	PAD	26 dB (CH1-4)
	Hi-Z	Supported (CH4)
	EQ HIGH	8kHz +15dB / -15dB
	EQ MID	2.5kHz +15dB / -15dB
	EQ LOW	100Hz +15dB / -15dB
On-board processors	DSP	SPX Algorithm Reverb 4 programs, MASTER EQ (SPEECH to MUSIC), Feedback suppressor
On-board amplifiers	Maximum output power @4ohms	1kHz THD+N less than 10% (CEA2006) : 250 W + 250 W, 1kHz THD+N less than 1% : 110 W + 110 W
On-board amplifiers	Maximum output power @8ohms	1kHz THD+N less than 10% (CEA2006) : 170 W + 170 W, 1kHz THD+N less than 1% : 110 W + 110 W
Level Meter		6points (-20, -6, 0 , +3, +6, LIMITER)

General specifications

Frequency response		Input to SPEAKERS : +1 dB/-4 dB (40Hz to 20kHz), Input to MONITOR OUT : +0.5 dB/-1.5 dB (20Hz to 20kHz) , refer to the nominal output level @ 1 kHz
Total harmonic distortion		Input to SPEAKERS : 0.2 % @ 13.8 W (40Hz to 20kHz), 0.4 % @ 23.2W (1kHz), Input to MONITOR OUT : 0.05 % @ +10 dBu (20Hz to 20kHz) 0.009 % @ +20 dBu (1kHz), (THD+N, Measured with 22 kHz LPF)
Hum & noise level	Equivalent input noise	-115 dBu
Hum & noise level	Residual output noise	Input to SPEAKERS : -68 dBu (40Hz to 20kHz, MASTER: min), Input to MONITOR OUT : -99 dBu (20Hz to 20kHz, MONITOR: min)
Crosstalk		-80 dB (1 kHz, Measured with 1 kHz band pass filter)
Protection circuit	Load protection	DC-fault
Protection circuit	Amplifier protection	Over heat protection, Over current protection
Power requirements		AC 100-240V, 50Hz/60Hz
Power consumption		35W (Idle) / 90W (1/8 Power)
Dimensions	W	375 mm (14.8")
	H	147 mm (5.8")
	D	220 mm (8.7")
Net weight		4.2 kg (9.3 lbs.)
Accessories		Owner’s Manual, Technical Specifications, Power Cord (2m)
Options		Foot Switch: FC5, Mic Stand Adaptor: BMS-10A, Rack mount kit RK-EMX2
Others		Operating Temperature : 0 to +40℃